Frequently Asked Question
To enter main programming first enter SYS1 settings:
Push 1 and * the screen will display "----"
then enter the 4 digits Admin pass-code 6666
The screen will display SYS1, the system is now ready to program. The original Admin pass-code is 6666
Pushing 0* will exit SYS1 from anywhere while programming.
1. Program Entry Doors
From SYS1 press 1* [Display will now show D01. if you have one door press 1* the system will say pass and will tone. For multi-door units, set each door station to match the port that door is run to on Multi-door switcher. Press 2* for two doors, press 3* for three doors and so on. The system will say pass and will tone and return to SYS1.]
[Special Notice:] Misconfiguring your door station ID will cause the following symptoms. This means, if you have one door station installed, it is imperative that you set the door station id to D01, if by any chance you have it set to any other ID such as D02 etc... you will not going to be able to:
a) manually engage the camera feed at the monitor without a call from the door station
b) you will not going to be able to change the monitor's ringtone.
2. Lowest Floor Level
From SYS1 press 2* [Should now show FL01. Press 1* to confirm. system will say pass and tone and return to SYS1.]
3. Highest Floor Level
From SYS1 press 3* [Should now show LL32. Set your floor number to one number above your actual total number of floors as the door counts as a floor. If you have 1 floor press 2*, if you have two floors press 3*, and so on. the system will say pass and tone and return to SYS1.]
4. Number of Rooms
From SYS1 press 4* [Should now show LR08. set the total number of room monitors the door you are programming will be calling. If you have 4 room monitors press 4*, for 5 press 5* and so on. the system will say pass and tone and return to SYS1.]
Press 0* to exit the system.
7. Room Programming [This stage requires back and forth between the door station and the adapter layers]
[When programming your room numbers you must enter 4 digits. I.E|.: room 1 on floor 1 would be programmed as 0101. The first two digits are the floor, the second two digits are the room number.Once the system is programmed you can use just the 3 core digits, 0101 can be activated by pressing 101]
*** PROGRAMMING ROOM NUMBERS ***
1. enter "sys1" programming mode - Press 1 * 6666 then 7 * (display says P1)
2. Press Layer Adapter#1 [BE-LA6] button ONE time - red LED light should begin flashing.
3. Next Press * then enter the first four digit room 0101(example 0101 would indicate room 101)
4. After entering the first number press ** ( this should say PASS and then P2 for the 2nd unit number)
5. screen should show "----" now enter the 2nd room number 0102 and hit ** (this should say PASS and then P3 for the 3rd unit number)
6. screen should show “----” now enter the 3rd room number 0103 and hit ** (this should say PASS and then P4 for the 4th unit number)
7. screen should show “----” now enter the 4th room number 0104 and hit ** (this should say PASS and then P5 for the 5th unit number)
8. screen should show “----” now enter the 5th room number 0105 and hit ** (this should say PASS and then P6 for the 6th unit number)
9. screen should show “----” now enter the 6th room number 0106 and hit * once and then # (display should say SYS1)
10. Press 0* to exit SYS1.
11. Finally Press Layer Adapter button ONCE to save SYS1 settings. (red LED light should stop flashing)
Now we will repeat the process with the 2nd layer adapter BE-LA6#2 for the remaining rooms to re-program.
1. enter "sys1" programming mode - Press 1 * 6666 then 7 * (display says P1)
2. Press Layer Adapter#2 [BE-LA6] button ONE time - red LED light should begin flashing.
3. Next Press * then enter the first four digit room 0107
4. After entering the first number press ** ( this should say PASS and then P2 for the 2nd unit number)
5. screen should show “----” now enter the 2nd room number 0108 and hit ** (this should say PASS and then P3 for the 3rd unit number)
6. screen should show “----” now enter the 3rd room number 0109 and hit ** (this should say PASS and then P4 for the 4th unit number)
7. screen should show “----” now enter the 4th room number 0110 and hit ** (this should say PASS and then P5 for the 5th unit number)
8. screen should show “----” now enter the 5th room number 0111 and hit ** (this should say PASS and then P6 for the 6th unit number)
9. screen should show “----” now enter the 6th room number 0112 and hit * once and then # (display should say SYS1)
10. Press 0* to exit SYS1.
11. Finally Press Layer Adapter button ONCE to save SYS1 settings. (red LED light should stop flashing)
At this point you are ready to test the units by calling them each one by one at the door station. If you can hear the ringtone calling the unit, then the programming was successful. If you get any error message on the display, then we will proceed differently.