Frequently Asked Question
[Master Card] User Instructions of RFID Access Control.
Last Updated 7 years ago
User Instructions of RFID Access Control.
This RFID Access module can save 2720 User cards / fobs and support quick
reading, changing Master card, adding User cards, deleting active user
cards, more convinience and reliable.What's more, there is a professional
RFID controller for better operation, and further needs has to be noted
additionally.
1) Make a master card: First, cut off the power of the outdoor
station, second, connect JP2 with power, then sound will be heard every
1.5 second,now to swipe new ID card will hear a long beep, that means new
master card has been made,finally to take off JP2 will exit.
2) Delete all user cards: First, cut off the power of the outdoor
station, then to connect JP3 with power,now a long beep will be heard,
that means all user cards has been deleted, finally to take off JP3 will
exit.
3) Initial Admin Password: First to cut off the power of the outdoor station,
then to connect JP1 with power, now a long beep wll be heard that means
Admin password has been intial as 1234, finally to take off JP1 will exit.
4) Add more user ID card:
Under standby, first swipe the Master card will come to the state of adding more user
cards, then to swipe the new ID card will hear a beep that means this new user cards
has been activated, finally swipe the Master card again will exit and back to standby
mode. Also, 2720 user ID card can be activated by one master card.
5) Open the door by ID user card:
Under standby, swipe the active access ID user card on the access window will
open the door, if the User card is not activated by the Master card, then the door can
not be open and a beep will be heard 3 times.
6) Add more user card by RFID Controller : Under standby, first, push * 1234
will hear a long beep, second, push * 2 and you will hear another long beep at every
1.5 seconds. That means it's time to add more user cards, Finally push * EXIT will exit.
P.S to swipe new user cards requires to add one by one, and a long beep will be hear
after adding one user card.
7) Delete some user cards by RFID Remote control: Under standby, firstly to push *
1234 will hear a long beep, secondly to push * 2 will hear another long beep at every
1.5 seconds. That means it's time to delete user cards, finally to push * EXIT will exit..
P.S: to delete the active user cards will hear a long beep, if the user card is not active,
then a long beep will be heard at 3 times.
8) Delete the user cards by serial numbers on the controller: Under standby,
firstly push *1234 will hear a long beep, second, push * 5 and you will hear another
long beep, then input the 10 digits serial number and # will hear a long beep that
means this user card has been deleted, finally to push * EXIT will exit. If the serial
number is wrong, then a long been will be heard at 3 times, so each serial number of
the user card has to be recorded at the beginning.
9) Delete all user cards by RFID controller : Under standby, first, push *1234
will hear a long beep, second, push * 6 will hear another long beep, then to push 1
2 # will stop the long beep that means all user cards has been deleted, finally push *
EXIT will exit.
10) Change Admin Password: Under standby, first, push *1234 will hear a
long beep, second, push * 1 will hear another
This RFID Access module can save 2720 User cards / fobs and support quick
reading, changing Master card, adding User cards, deleting active user
cards, more convinience and reliable.What's more, there is a professional
RFID controller for better operation, and further needs has to be noted
additionally.
1) Make a master card: First, cut off the power of the outdoor
station, second, connect JP2 with power, then sound will be heard every
1.5 second,now to swipe new ID card will hear a long beep, that means new
master card has been made,finally to take off JP2 will exit.
2) Delete all user cards: First, cut off the power of the outdoor
station, then to connect JP3 with power,now a long beep will be heard,
that means all user cards has been deleted, finally to take off JP3 will
exit.
3) Initial Admin Password: First to cut off the power of the outdoor station,
then to connect JP1 with power, now a long beep wll be heard that means
Admin password has been intial as 1234, finally to take off JP1 will exit.
4) Add more user ID card:
Under standby, first swipe the Master card will come to the state of adding more user
cards, then to swipe the new ID card will hear a beep that means this new user cards
has been activated, finally swipe the Master card again will exit and back to standby
mode. Also, 2720 user ID card can be activated by one master card.
5) Open the door by ID user card:
Under standby, swipe the active access ID user card on the access window will
open the door, if the User card is not activated by the Master card, then the door can
not be open and a beep will be heard 3 times.
6) Add more user card by RFID Controller : Under standby, first, push * 1234
will hear a long beep, second, push * 2 and you will hear another long beep at every
1.5 seconds. That means it's time to add more user cards, Finally push * EXIT will exit.
P.S to swipe new user cards requires to add one by one, and a long beep will be hear
after adding one user card.
7) Delete some user cards by RFID Remote control: Under standby, firstly to push *
1234 will hear a long beep, secondly to push * 2 will hear another long beep at every
1.5 seconds. That means it's time to delete user cards, finally to push * EXIT will exit..
P.S: to delete the active user cards will hear a long beep, if the user card is not active,
then a long beep will be heard at 3 times.
8) Delete the user cards by serial numbers on the controller: Under standby,
firstly push *1234 will hear a long beep, second, push * 5 and you will hear another
long beep, then input the 10 digits serial number and # will hear a long beep that
means this user card has been deleted, finally to push * EXIT will exit. If the serial
number is wrong, then a long been will be heard at 3 times, so each serial number of
the user card has to be recorded at the beginning.
9) Delete all user cards by RFID controller : Under standby, first, push *1234
will hear a long beep, second, push * 6 will hear another long beep, then to push 1
2 # will stop the long beep that means all user cards has been deleted, finally push *
EXIT will exit.
10) Change Admin Password: Under standby, first, push *1234 will hear a
long beep, second, push * 1 will hear another