Frequently Asked Question

Here is your parameter for the configuration of the door station and monitors:

[NT-IP-DRCR, G9W] Settings - Door panel to ring/call monitor

If you are having problem to connect your DRCR door station to call/contact your G9WS monitor, the following is likely the settings to copy. Special note: this monitor does not have explicit floor number identification, rather, it is incorporated into the room number as you will see bellow.

To start, I suggest to leave the default IP address at the door station and change each monitors IP addresses to allow networking communication as all devices have the same IP address which if not changed will cause conflict. To do that, follow these steps:

1. On the main screen of the 1st monitor, look in the upper right corner for the APPS icon.
2. Click on it.
3. Next, select Browser
4. On the browser url (address bar) type: 127.0.0.1 ( when at the monitor only) and hit Go
5. On the next screen a login window will pop up. Use the following:
6. username: admin
7. password: 123456
8. Now you are ready to proceed.

Step #1 The network or LAN settings need to be adjusted to match both door station and monitor (s).

Network Settings [DRCR door station] Leave the default
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.90 [default IP address]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
Server IP: [IP address of the laptop / PC managing the system]
Password: 123456

Network Settings [G9W monitor] #1
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.101
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]

Network Settings [G9W monitor] #2
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.102
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]

Network Settings [G9W monitor] #3
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.103
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]

Network Settings [G9W monitor] #4
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.104
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]

Network Settings [G9W monitor] #5
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.105
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]

Network Settings [G9W monitor] #6
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.106
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]

Step #2, to setup the device/Room settings to match both monitors with the door station.

Device Settings [Door Panel/Door station: NT-IP-DRCR]
192.168.68.90 [Main Panel] [IP address is as an example]
BuildNo: 1
UnitNo: 1

Floor: 1

RoomNo: 1

No.: 1
Sys passwd: ••••••
Panel mode: Person Panel
Forward: All at Once

Room Settings [Monitor]192.168.68.101 [monitor #1] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 0
Sync: ######

Server: 192.168.###.###
Password: 123456

192.168.68.102 [monitor #2] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 1
Sync: ######

192.168.68.103 [monitor #3] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 2
Sync: ######

192.168.68.104 [monitor #4] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 3
Sync: ######

192.168.68.105 [monitor #5] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 4
Sync: ######

192.168.68.106 [monitor #6] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 5
Sync: ######

Wiring Diagrams Options - Using an Altronix Relay 6062 Module

Wiring Diagrams Options - Using a direct connection to the AC powered lock