Frequently Asked Question
What you need to communicate from the DRS1 to your monitor is the correct (LAN) network settings being on the same subnet, and the correct Device vs Room settings so the DRS1 knows where to call or how to reach the monitors. That's it.
Anything else, are just bells and whistles.
Let's start afresh with your settings.
This will provide guidance if a followup call is needed.
- [if unsure of the IP address, use the Loopback IP address: 127.0.0.1 when at the monitor only]
- To use the monitor's browser. The browser is located in the upper right corner of the main window, select Apps, then, on the next screen, select Browser.
- In the browser address bar, use 127.0.0.1 and hit Go.
Here is your parameter for the configuration of the door station and monitors:
[NT-IP-DRS1, G9W] Settings - Door panel to ring/call monitor
If you are having problem to connect your A9K door station to call/contact your G9WS monitor, the following is likely the settings to copy. Special note: this monitor does not have explicit floor number identification, rather, it is incorporated into the room number as you will see bellow.
Step #1 The network or LAN settings need to be adjusted to match both door station and monitor (s).
Network Settings [DRS1 door station #1]
DHCP: [unchecked if static IP address is used][checked if a router will assign the route]
IP: 192.168.68.90 [default IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
Server IP: [IP address of the laptop / PC managing the system]
Password: 123456
NTP: 198.123.30.132
Network Settings [DRS1 door station #2]
DHCP: [unchecked if static IP address is used][checked if a router will assign the route]
IP: 192.168.68.91 change from default [IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
Server IP: [IP address of the laptop / PC managing the system]
Password: 123456
NTP: 198.123.30.132
Network Settings [DRS1 door station #3]
DHCP: [unchecked if static IP address is used][checked if a router will assign the route]
IP: 192.168.68.92 [default IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
Server IP: [IP address of the laptop / PC managing the system]
Password: 123456
NTP: 198.123.30.132
Network Settings [DRS1 door station #4]
DHCP: [unchecked if static IP address is used][checked if a router will assign the route]
IP: 192.168.68.93 change from default [IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
Server IP: [IP address of the laptop / PC managing the system]
Password: 123456
NTP: 198.123.30.132
Network Settings [G9W monitor] #1
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.101 [default IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]
Network Settings [G9W monitor] #2
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.102 [default IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]
Network Settings [G9W monitor] #3
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.103 [default IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]
Network Settings [G9W monitor] #4
DHCP: [unchecked if static IP address is used]
IP: 192.168.68.104 [default IP address: 192.168.68.90]
Mask: 255.255.255.0
Gateway: 192.168.68.1
DNS: 8.8.8.8
eth & wifi: [checked]
Step #2, to setup the device/Room settings to match both monitors with the door station.
Device Settings [Door Panel/Door station: NT-IP-DRS1 #1]
192.168.68.90 [Main Panel] [IP address is as an example]
BuildNo: 1
UnitNo: 1
RoomNo: 1111
No: 1
Sys passwd: 123456
Panel mode: Person Panel
Ring back: Ring02
Language: English
Volume: 3
TZ: GMT-05
Forward: All at Once
Device Settings [Door Panel/Door station: NT-IP-DRS1 #2]
192.168.68.91 [Main Panel] [IP address is as an example]
BuildNo: 1
UnitNo: 1
RoomNo: 1111
No: 2
Sys passwd: 123456
Panel mode: Person Panel
Ring back: Ring02
Language: English
Volume: 3
TZ: GMT-05
Forward: All at Once
Device Settings [Door Panel/Door station: NT-IP-DRS1 #3]
192.168.68.92 [Main Panel] [IP address is as an example]
BuildNo: 1
UnitNo: 1
RoomNo: 1111
No: 3
Sys passwd: 123456
Panel mode: Person Panel
Ring back: Ring02
Language: English
Volume: 3
TZ: GMT-05
Forward: All at Once
Device Settings [Door Panel/Door station: NT-IP-DRS1 #4]
192.168.68.93 [Main Panel] [IP address is as an example]
BuildNo: 1
UnitNo: 1
RoomNo: 1111
No: 4
Sys passwd: 123456
Panel mode: Person Panel
Ring back: Ring02
Language: English
Volume: 3
TZ: GMT-05
Forward: All at Once
Room Settings [Monitor]192.168.68.101 [monitor #1] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111 [3 to 4 digits as the first as follow: 0101 or 1201] first two digit represents the floor, and last two digit represents the room#
Device: 0
Sync: 123456
Server: 192.168.###.### [IP address of the laptop / PC managing the system]
Password: 123456
192.168.68.102 [monitor #2] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 1
Sync: 123456
Server: 192.168.###.### [IP address of the laptop / PC managing the system]
Password: 123456
192.168.68.103 [monitor #3] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 2
Sync: 123456
Server: 192.168.###.### [IP address of the laptop / PC managing the system]
Password: 123456
192.168.68.103 [monitor #4] NT-IP-G9W
Room No. Settings
Build: 1
Unit: 1
Room: 1111
Device: 3
Sync: 123456
Server: 192.168.###.### [IP address of the laptop / PC managing the system]
Password: 123456
Cat5/cat6 cable pinout:
Wiring Diagrams Options - Using an Altronix Relay 6062 Module
* The monitors depicted in the above image re the NT-IP-7B or the NT-IP10 - those are the only models with WiFi capabilities.